General Interest

Classic Japanese Motorcycles

Remote Control & Touchkeys

Remote Fobs

Before ordering a replacement touchkey/remote please check that you are able to enter programming mode by following the instructions below

If you are unsure of which Selca device you have fitted to your car check the following:

Look under the bonnet of the vehicle and locate the siren, if you cannot find it and only have touchkeys but no remote controls the chances are the IM3.22 is fitted. If there is a siren and is marked FC6.00 or FC6.01 go to FC range programming. If the siren is marked FC6.5 the FM7 is fitted.

To program a new fob into the FC6 & FC6.01 a working fob is required without which the process will not be possible.

To program a new fob into the FM7 & FC6.71 a working touchkey is required without which the process will not be possible.

To program a new fob into the Splitt range a 4 digit pin number is required without which the process will not be possible. If you do not have this code number please contact the office.

Selca Two Button Remote for FM7, FC6, FC6.01, FC6.71 & Split range, will also work for single button systems

Buy Online

STK1 TOUCH KEY

Selca Touch Key for FM7, FC671, IM3.22 & Splitt systems

Please note you must have at least one working remote or touchkey to program new remotes into most Selca alarm systems

IMPORTANT - IM3.22 Immobiliser Notice
Before ordering a replacement Selca Touch Key please make sure you have the master RED key which without it will not be possible to do. Plus please check your IM3.22 immobiliser can go into program mode by following the instructions below. Many of these immobilisers have not been fitted correctly and as such will never be able to program new keys in even though they seem to function correctly as an immobiliser.

To check whether the Immobiliser has been correctly fitted to your vehicle please follow the instructions below.

1. Sit inside the vehicle and close all the doors.
2. Disarm the immobiliser with any working touchkey; the immobiliser LED will flash quickly.
3. Turn on the ignition (do not start the car) wait 10 seconds, switch off ignition.
4. Open the drivers door making sure the vehicle's interior light illuminates, after approx. 5 seconds close the door.
5. The immobiliser LED should flash quickly for the next (approximately) 30-50 seconds after this period the LED will flash slowly indicating a fully immobilised state. If this occurs the immobiliser will be able to enter programming mode and new touchkeys can be programmed into the system (working RED key required). If the immobiliser is still flashing quickly (for the next 3 minutes or so), programming mode cannot be entered and new touchkeys cannot be programmed into the system. Contact the office on 0208 677 1999 for further help.
   

Buy Online

 

For programming instructions see below.

LOST THE RED MASTER KEY?

If the red master key is lost/broken we can now supply a relatively easy kit to completely replace the existing control unit mounted inside the IM3.22 control box.

For More Information & Fitting Instructions click here

Buy the kit Online

Selca programming Instructions

FC range Programming

FM7 & FC 6.71 Programming

IM3.22 Programming

MT8 Motorcycle Alarm

BACK

Programming Selca Remotes (pdf)

• FM7 & FC6.71
• IM3 range
• FC range

  Online Shop

  Selca RC42 Two Button Remote for FM7, FC6, FC6.01, FC6.71, MT8 & Split 88 range, will also work for single button systems

  

  Buy Online

  For programming instructions see below.

  ---

   

  Selca STK1 self coding touchkey for the FM7, FC6.71 & IM3 range of immobilisers. For programming instructions see information on the left.

  
  Buy Online

  For programming instructions see below.

  ---

   

  STK1 Replacement Red Key
  

  IM3.22 Service Kit. If the master RED key is lost this kit can completely replace the existing unit.

  More Info

  Order Online