General Interest

Classic Japanese Motorcycles

GEMEL SERPI STAR

SERPI STAR GEMEL REMOTES

We can only supply SELF CODING two button remotes like the one pictured above for Gemel Serpi Star Alarms

Coding New Gemel/Serpi Star Fobs
In addition to a new self coding remote you will require either an override key, touchkey or an emergency code number to program it into the main alarm brain, without any of these it will not be possible to code in a new remote. This remote will also work with the Meta M999T (five digit override code required)

Some of the ND range of alarms require the on/off key for programming new remotes, Click here if the on/off keys are not available.

BUY 2 Button Remote ONLINE

Single button remote controls are no longer available and are not compatible with the two button models. If lost or broken the alarm will need removing or replacing.

Single button remotes & spare parts are no longer available

If you are not sure whether your remote control is self coding (random encrypted) or fixed code type carry out he following procedure:

Press both buttons simultaneously and hold, the LED should flash quickly, after 10 seconds the LED light goes out, release both buttons, the LED will now stay on constantly, press and release any button and the LED will go out. 

If your remote does not do the above than you have the fixed code variety, this remote control is no longer available.

If you have the old oblong unit with a corner cut out of it we are no longer able to supply this product (note that later versions of the oblong remote are self coding and the above remote can be programmed into your alarm system).

Self learning procedures

(5 digit pin code required for GR99, touchkey required for GR 470/480, on/off keys required for ND5, ND6 & ND14

Note If you do not have the touch keys it will be impossible to program a new remote into the system.

1. Open the drivers door and keep it open Turn on the ignition and leave it on.
2. Turn the emergency override key on the alarm to the OFF position wait a few seconds then back ON -Entry into the self learning mode will be signaled by 3 beeps on the siren.
3. For alarms systems equipped with touch key override keys, insert the first key in the receptacle on the dash and keep it there until the beeps on the siren are heard, remove the touch key as you are now in self learning mode.
4. Once in programming mode, make sure you are very close to the vehicle, take the first transmitter and press both buttons at the same time, the LED on the remote will flash quickly, keep pressing both buttons until the LED stops flashing (at least 10 seconds). Once LED is extinguished stop pressing the buttons the LED on the remote will stay on, press and release either button on the remote, you should now hear a beep from the alarm. The remote is now programmed into the alarm. All old remotes will now be removed from the alarms memory so you will have to repeat the above procedure for all the other remotes in your possession, also touch all the touch keys onto the receptacle to program them in.
5. To exit the self learning procedure turn off the ignition key.

Programming remotes into the ND5 & ND6 and most ND Range ALARM SYSTEMS (not ND14):

Programming remotes into E series and alarms with emergency override codes

Click for printable version

Coding Procedure for alarms with remote controls and Touchkeys for most of the GR range & the ND14

This system can be programmed with up to a maximum of 4 Remotes and 4 Electronic Override Keys at any one time. All Remotes required to operate this system must be present and programmed at the same time. Enter the Self Learning mode by:

1. Open the drivers door and leave it open.
2. Turn the ignition to 'ON'. Do not start the engine.
3. Momentarily touch one of the Electronic override keys onto the dashboard LED/Reader. The siren will give 3 audible tones to indicate entry into the Self Learning mode.
4. Pick up one of the remotes and press both buttons simultaneously until the LED of the remote goes out. (Approximately 10 seconds). Release both buttons and the LED will come on constantly.
5. Depending on the type of remote press either the red or the ribbed button once. This will be acknowledged by: either/or a single flash of the dashboard LED/Reader or/and a single tone of the siren. This remote has now been programmed
6. Repeat steps D & E to code the remaining remotes.
7. When all the remotes have been programmed, turn the ignition to 'OFF. This will be acknowledged by 3 siren tones. Test each Remote to ensure correct operation.

Electronic Override Keys

All Override keys, including at least one of the originals, required to operate this system must be present and programmed at the same time. Enter the Self Learning mode by:

1. Open the door to which the Yellow wire is connected and leave it open.
2. Turn the ignition to the 'ON' position. Do not start the engine.
3. Momentarily touch one of the Electronic override keys onto the dashboard LED/Reader. The siren will give 3 audible tones to indicate entry into the Self Learning mode
4. First touch one of the Original Override keys onto the dashboard LED/Reader. This will be acknowledged by:either/or a single flash of the LED and/or a single tone of the siren.
5. This Override key has now been programmed
   Repeat step (3) for ALL the remaining Override Keys including the one that was originally used.
6. Once all the Electronic Override Keys have been programmed, turn the ignition 'OFF. This will be signaled be 3 siren tones. Test each key to ensure correct operation. (Refer to User Instructions).

NOTE: IT IS IMPORTANT TO KEEP THE ORIGINAL OVERRIDE KEYS ' IN A SAFE PLACE AS AT LEAST ONE OF THEM MUST ALWAYS BE USED IN THE PROGRAMMING PROCEDURE.

Click here to order a Serpi Star/Gemel two button remote control

Programming Gemel/Serpi Star Remotes (pdf):

• ND Range
• GR99
• GR480

Online Shop

2 Button Remote
Serpi/Star Gemel 2 Button Self Coding Remote Control. For programming instructions see left panel below

BUY ONLINE

Gemel/Serpi Star 'DR' Touchkey

  Serpi Star Gemel DR Touchkey for the GR470 & 480 range of alarm systems. Please note you will require a working touchkey to program a new key into the system. Once a DR override touchkey has been programmed into any of the Serpi Star systems it will be impossible to program the same key into another. For this reason we are unable to take back unwanted touchkeys.
Sorry this product is no longer available

Lost the on/off keys for the ND range of alarms