Abacus Car Alarms

General Interest

Classic Japanese Motorcycles

SERPI STAR GEMEL REMOTES

Buy Online

We can only supply SELF CODING remotes like the one pictured above for Gemel Serpi Star Alarms

Coding Serpi Star Remotes On Most Systems (Self learning procedure)

Open the drivers door and keep it open

Turn on the ignition and leave it on.

EITHER

1- Turn the emergency over-ride key on the alarm to the OFF position wait a few seconds then back ON -Entry into the self learning mode will be signaled by 3 beeps on the siren.

2- For alarms systems equipped with touch key over-ride keys, insert the first key in the receptacle on the dash and keep it there until the beeps on the siren are heard, remove the touch key as you are now in self learning mode.

Note If you do not have the touch keys than it is impossible to program a new remote into the system.

.Once in programming mode, make sure you are very close to the vehicle, take the first transmitter and press both buttons at the same time, the LED on the remote will flash quickly, keep pressing both buttons until the LED stops flashing (approx. 10 seconds). Once LED is extinguished stop pressing the buttons the LED on the remote will stay on, press and release any button on the remote, you should now hear a beep from the alarm. The remote is now programmed into the alarm. All old remotes will now be removed from the alarms memory so you will have to repeat the above procedure for all the other remotes, also touch all the touch keys onto the receptacle to program them in.

To exit the self learning procedure

Turn off the ignition key.

If you are not sure whether your remote control is self coding carry out he following procedure:

Press both buttons simultaneously and hold, the LED should flash quickly, after 10 seconds the LED light goes out, release both buttons, the LED will now stay on constantly, press and release any button and the LED will go out. 

If your remote does not do the above than you have the fixed code variety and I am afraid we are unable to help you. 

If you have the old oblong unit with a corner cut out of it we are no longer able to supply this product (note that later versions of the oblong remote are self coding and the above remote can be programmed into your alarm system).

Programming remotes into the ND5 & ND6 ALARM SYSTEMS:

Coding Procedure on Alarms with Touch-keys

GR400 range

Remote Controls

This system can be programmed with up to a maximum of 4 Remotes and 4 Electronic Override Keys at any one time. All Remotes required to operate this system must be present and programmed at the same time. Enter the Self Learning mode by: A) Open the door to which the Yellow wire is connected and leave it open. B) Turn the ignition to 'ON'. Do not start the engine. C) Momentarily touch one of the Electronic override keys onto the dashboard LED/Reader. The siren will give 3 audible tones to indicate entry into the Self Learning mode.

Programming Remotes

D) Pick up one of the remotes and press both buttons simultaneously until the LED of the remote
goes out. (approximately 10 seconds). Release both buttons and the LED will come on constantly.
E) Depending on the type of remote press either the red or the ribbed button once. This will be
acknowledged by:
? a single flash of the dashboard LED/Reader.
? a single tone of the siren.
This remote has now been programmed
Repeat steps D & E to code the remaining remotes.

When all the remotes have been programmed, turn the ignition to 'OFF. This will be acknowledged by 3 siren tones. Test each Remote to ensure correct operation.

Electronic Override Keys All Override keys, including at least one of the originals, required to operate this system must be present and programmed at the same time. Enter the Self Learning mode by: A) Open the door to which the Yellow wire is connected and leave it open. B) Turn the ignition to the 'ON' position. Do not start the engine. C) Momentarily touch one of the Electronic override keys onto the dashboard LED/Reader. The siren will give 3 audible tones to indicate entry into the Self Learning mode

D) First touch one of the Original Override keys onto the dashboard LED/Reader. This will be
acknowledged by:
? a single flash of the LED
? a single tone of the siren.
This Override key has now been programmed
Repeat step (D) for ALL the remaining Override Keys including the one that was used in step (C).

Once all the Electronic Override Keys have been programmed, turn the ignition 'OFF. This will be signalled be 3 siren tones. Test each key to ensure correct operation. (Refer to User Instructions).

Buy Online

NOTE: IT IS IMPORTANT TO KEEP THE ORIGINAL OVERRIDE KEYS ' IN A SAFE PLACE AS AT LEAST ONE OF THEM MUST ALWAYS BE USED IN THE PROGRAMMING PROCEDURE.